Fundamentals of Machining, Metrology and Product Design

Garant předmětu:

Petr Mikeš

Lecturer:

Petr Mikeš, Vítězslav Rázek

Tutor:

Petr Mikeš, Zdeněk Pitrmuc, Vítězslav Rázek, Michal Slaný

Supervisor:

Department of Machining, Process Planning and Metrology

Synopsis:

Introduction to machining. Principle of cutting process. Working parameters. Cutting tools - general characteristics, geometry, designation and symbols. The basic machining processes, their mechanics, equipment, conditions, material removal rate determination. The shapes produced, commercial tolerance and surface finish obtained. Laboratories.

Requirements:

(nothing)

Syllabus of lectures:

1) Basic production technologies, development of machining technologies and their division, basic concepts

2) Geometry of cutting tools - tool planes

3) Tool materials, coatings, overview, properties, use, correct tool selection, calculation of tool costs

4) Machining of rotating surfaces, achieved quality parameters - turning

5) Machining of flat and shaped surfaces, achieved quality parameters - milling

6) Clamping of tools and workpieces during turning and milling

7) Tool wear, causes of tool wear, course of wear, Taylor's relation, prediction of wear

8) Machining temperature, heat dissipation and heat balance, machining forces, chip formation, selection and optimization of cutting conditions

9) Machining of holes - drilling, boring, reaming, boring, shaping, broaching, machines and tools, clamping, material cutting

10) Finishing rotating surfaces, grinding and other technologies to achieve the highest quality and accuracy of surfaces

11) Finishing non-rotating surfaces, grinding and other technologies to achieve the highest quality and accuracy of surfaces

12) Achieved dimensional accuracy and surface quality of basic production technologies, basic means for quality control

13) Technological procedure, economics of machining process, optimization procedures, selection of suitable technology

Syllabus of tutorials:

1) Induction course, organization of laboratory works, safety standards, basic terminology of machining process.

2) Basic terminology of machining process - laboratory practice.

3) Basic terminology of machining process - cutting tools.

4) Real shop practice.

5) Real shop practice.

6) Real shop practice.

7) Credit test, submission of specifications, credit.

Study Objective:

Knowledge of basic methods of the machining and a quiddity of the cutting process.

Study materials:

Boothroyd, G., Knight, W. A. Fundamentals of Machining and Machine Tools. Marcel Dekker, Inc., New York and Basel, 1989

Note:

Time-table for winter semester 2024/2025:

	06:00–08:0008:00–10:0010:00–12:0012:00–14:0014:00–16:0016:00–18:0018:00–20:0020:00–22:0022:00–24:00
Mon
Tue
Wed	roomT4:D1-366 Mikeš P. Rázek V. 10:45–12:15 (lecture parallel1) Dejvice Posluchárna 366roomT4:E3-27 Pitrmuc Z. Mikeš P. 12:30–13:15 EVEN WEEK (lecture parallel1 parallel nr.101) Dejvice Laboratoř obrábění 12134roomT4:E3-27 Mikeš P. 13:15–14:00 EVEN WEEK (lecture parallel1 parallel nr.101) Dejvice Laboratoř obrábění 12134roomT4:E3-27 Mikeš P. Pitrmuc Z. 16:00–16:45 ODD WEEK (lecture parallel1 parallel nr.103) Dejvice Laboratoř obrábění 12134roomT4:E3-27 Mikeš P. 16:45–17:30 ODD WEEK (lecture parallel1 parallel nr.103) Dejvice Laboratoř obrábění 12134 roomT4:E3-27 Pitrmuc Z. Mikeš P. 12:30–13:15 ODD WEEK (lecture parallel1 parallel nr.102) Dejvice Laboratoř obrábění 12134roomT4:E3-27 Pitrmuc Z. 13:15–14:00 EVEN WEEK (lecture parallel1 parallel nr.101) Dejvice Laboratoř obrábění 12134roomT4:E3-27 Pitrmuc Z. 16:45–17:30 ODD WEEK (lecture parallel1 parallel nr.103) Dejvice Laboratoř obrábění 12134 roomT4:E3-27 Rázek V. 13:15–14:00 EVEN WEEK (lecture parallel1 parallel nr.101) Dejvice Laboratoř obrábění 12134roomT4:E3-27 Rázek V. 16:45–17:30 ODD WEEK (lecture parallel1 parallel nr.103) Dejvice Laboratoř obrábění 12134 roomT4:E3-27 Mikeš P. 13:15–14:00 ODD WEEK (lecture parallel1 parallel nr.102) Dejvice Laboratoř obrábění 12134roomT4:E3-27 Mikeš P. Pitrmuc Z. 16:00–16:45 EVEN WEEK (lecture parallel1 parallel nr.104) Dejvice Laboratoř obrábění 12134roomT4:E3-27 Mikeš P. 16:45–17:30 EVEN WEEK (lecture parallel1 parallel nr.104) Dejvice Laboratoř obrábění 12134 roomT4:E3-27 Pitrmuc Z. 13:15–14:00 ODD WEEK (lecture parallel1 parallel nr.102) Dejvice Laboratoř obrábění 12134roomT4:E3-27 Pitrmuc Z. 16:45–17:30 EVEN WEEK (lecture parallel1 parallel nr.104) Dejvice Laboratoř obrábění 12134 roomT4:E3-27 Rázek V. 13:15–14:00 ODD WEEK (lecture parallel1 parallel nr.102) Dejvice Laboratoř obrábění 12134roomT4:E3-27 Rázek V. 16:45–17:30 EVEN WEEK (lecture parallel1 parallel nr.104) Dejvice Laboratoř obrábění 12134
Thu
Fri	roomT4:E3-27 Rázek V. Mikeš P. 10:45–11:30 ODD WEEK (lecture parallel1 parallel nr.105) Dejvice Laboratoř obrábění 12134roomT4:E3-27 Mikeš P. 11:30–12:15 ODD WEEK (lecture parallel1 parallel nr.105) Dejvice Laboratoř obrábění 12134room Rázek V. Mikeš P. 12:30–13:15 ODD WEEK (lecture parallel1 parallel nr.107) room Mikeš P. 13:15–14:00 ODD WEEK (lecture parallel1 parallel nr.107) roomT4:E3-27 Rázek V. Mikeš P. 10:45–11:30 EVEN WEEK (lecture parallel1 parallel nr.106) Dejvice Laboratoř obrábění 12134roomT4:E3-27 Pitrmuc Z. 11:30–12:15 ODD WEEK (lecture parallel1 parallel nr.105) Dejvice Laboratoř obrábění 12134room Pitrmuc Z. 13:15–14:00 ODD WEEK (lecture parallel1 parallel nr.107) roomT4:E3-27 Rázek V. 11:30–12:15 ODD WEEK (lecture parallel1 parallel nr.105) Dejvice Laboratoř obrábění 12134room Rázek V. 13:15–14:00 ODD WEEK (lecture parallel1 parallel nr.107) roomT4:E3-27 Mikeš P. 11:30–12:15 EVEN WEEK (lecture parallel1 parallel nr.106) Dejvice Laboratoř obrábění 12134 roomT4:E3-27 Pitrmuc Z. 11:30–12:15 EVEN WEEK (lecture parallel1 parallel nr.106) Dejvice Laboratoř obrábění 12134 roomT4:E3-27 Rázek V. 11:30–12:15 EVEN WEEK (lecture parallel1 parallel nr.106) Dejvice Laboratoř obrábění 12134

Time-table for summer semester 2024/2025:

Time-table is not available yet

The course is a part of the following study plans: