Analog Signal Processing and Digitalization

Vztahy:

In order to register for the course A8M38ASP, the student must have registered for the required number of courses in the group BEZBM no later than in the same semester.

Garant předmětu:

Josef Vedral

Lecturer:

Michal Janošek, Josef Vedral

Tutor:

Michal Janošek, Josef Vedral

Supervisor:

Department of Measurement

Synopsis:

The course is dedicated to methods for preprocessing, digitalization and reconstruction of continuis signals. It is focused to the methods for achieving of high precision of transmission and suppression of spurious components. The laboratory exercises are divided into two parts: the first part is classical tasks; the second one is individual project of design of typically data acqusition system. The teaching is supported by the CAD system for measuring circuits.

Requirements:

Syllabus of lectures:

1. Operational amplifiers for signal conditioning, negative feedback

2. Voltage, current, integration, charge, differential, instrumentation, insulation amplifiers

3. Signal processing for resistive, capacitance and inductance sensors, coherent detection

4. Signal processing for RTD, thermocouple and semiconductor temperature sensors

5. Methods of nonlinear signal processing, signal compression and expansion

6. Nonharmonic signal processing, rectifiers, RMS and peak to peak converters

7. Signal filtering, analog and switching filters design and application

8. Analog signals multiplexing and sampling, voltage references

9. High speed signal digitization, sampling, quantization, flash, half-flash and approximation A/D converters

10. High resolution signal digitization, integration and delta sigma A/D converters, dithering

11. Signal reconstruction, direct digital synthesis

12. Spectral analysis periodic and non-periodic signals, windowing

13. Testing of digitizers, sine wave fit test, spectral frequency test, histogram test

14. Hardware design techniques of A/D systems, grounding, shielding, noise reduction

Syllabus of tutorials:

1. Static, dynamic and noise amplifier parameters

2. Resistive bridge signal conditioning and processing, instrumental amplifiers

3. Capacitive sensor circuits, synchronous detection

4. Thermocouple and RTD temperature sensor circuits

5. Analog filters - LP, HP, BP, BS, universal filters

6. Signal switching and sampling

7. Logarithmic, exponential amplifiers, multipliers

8. Mean, RMS and peak value detectors

9. Signal digitization, sampling, SNR

10. Signal reconstruction, DDS

11. Project - introduction, problem definition

12. Project - analogue part analysis

13. Project - signal AD conversion analysis

14. Results evaluation, assessment

Study Objective:

Study materials:

1. Vedral, Svatoš: Zpracování a digitalizace analogových signálů v měřicí technice. Česká technika 2018. ISBN: 978-80-01-06424-5

2.Vedral, Svatoš: Analog signal processing and digitization. Česká technika 2010. ISBN:978-80-01-06717-8

3. Pallas Areny, Webster: Sensor and signal conditioning. John Wiley Sons, 2001, ISBN 0-471-3323-1

Note:

Further information:

https://moodle.fel.cvut.cz/courses/A8M38ASP

Time-table for winter semester 2024/2025:

	06:00–08:0008:00–10:0010:00–12:0012:00–14:0014:00–16:0016:00–18:0018:00–20:0020:00–22:0022:00–24:00
Mon
Tue	roomT2:A3-316 Vedral J. 12:45–14:15 (lecture parallel1 parallel nr.1) Dejvice Laboratoř ZSroomT2:A3-316 Vedral J. 16:15–17:45 (lecture parallel1 parallel nr.2) Dejvice Laboratoř ZS roomT2:C2-82 Vedral J. Janošek M. 14:30–16:00 (lecture parallel1) Dejvice T2:C2-82
Wed
Thu
Fri

Time-table for summer semester 2024/2025:

Time-table is not available yet

The course is a part of the following study plans:

• Otevřené elektronické systémy - Integrované elektronické systémy (compulsory course of the specialization)