Industrial Electrical Engineering
- Department of Electrotechnology
A student will, at first, meet with information about basic types of materials for electrical engineering, their properties, technologies and applications. The next task is focused on the fundamentals, function and service characteristics of transformers, power electronic converters, generators, DC and AC motors and contact electric apparatus. The problems are tested on the mains supply real units. The third part of the course deals with power electrical engineering, with the basic characteristic of a power system in the Czech Rep. and with types, operational modes and environmental impact of different types of power sources.
Active attendance and accomplishment of tasks at tutorials are necessary conditions for award an assessment. A student must get an assessment before an examination. A knowledge of a lectured and tutorial matters will be required at examination.
- Syllabus of lectures:
1.Conductive and superconductive properties of materials, conductors, superconductors and their selected applications.
2.Dielectric and insulating properties of materials, dilectric and insualting materials used in electrical engineering. Dielectric and HF heating.
3.Semiconductive properties of materials, basic types of semiconductors. Production and processing of single-crystals, IO technology, chips bonding.
4.Magnetic properties of materials and basic magnetic materials for electrical engineering. Thin and thick films.
5.Lasers and laser technologies.
6.Technology based on electron beam - lithography, machining, welding.
7.Electric energy sources. Transformers, rectifiers.
8.DC motors with mechanical and electronic commutation.
9.Induction and synchronous motors and generators.
10.Electric apparatus. DC and AC circuits switching.
11.Contemporary state and the strategy of power engineering development. Fundamentals of the power legislation.
12.Structure and operational characteristics of the power system in CR. Systems for transmission and distribution of electric power.
13.Structure and operational characteristics of power plants (thermal, hydroelectric, nuclear, alternative power plant).
14.Operational modes of power sources, their influence on the environment.
- Syllabus of tutorials:
1.Work safety at laboratory. Presentation of laboratory tasks.
2.Properties of semiconducting Si.
3.Measurement of anizotropy of transformer sheets.
4.Joining of power cables.¨
5.Soft soldering in electrical engineering.
6.Full-wave bridge rectifier at R , RL load.
7.Separately excited DC motor. Permanent magnet brushless DC motor.
8.Induction motor supplied by network and by frequency converter.
9.Contactor circuit control of induction motor
10.Daily load diagram covering.
11.Steady states calculations in the systems.
12.Balance calculations in power plants.
13.Excursion to a power plant.
- Study Objective:
Student will learn basic types of materials for electrical production, basic types of electrical machines, apparatusses and drivers and with basic types of power stations and distribution nets.
- Study materials:
1.Bruce, R. G. et al.: Modern Materials and Manufacturing Processes, Prentice Hall, 2003
2.Brown, W. D.: Advanced Electronic Packaging, IEEE Press, 1998
3.Weedy B. M.: Electric Power System, 1992
4.Stephen, J. C.: Electric machinery fundamentals, Mc. Graw - Hil publishing Co., 1985
- Further information:
- No time-table has been prepared for this course
- The course is a part of the following study plans:
- Cybernetics and Robotics - Robotics (elective course)
- Cybernetics and Robotics - Senzors and Instrumention (elective course)
- Cybernetics and Robotics - Systems and Control (elective course)
- Electrical Engineering, Power Engineering and Management - Applied Electrical Engineering (elective course)
- Electrical Engineering, Power Engineering and Management - Electrical Engineering and Management (elective course)
- Communications, Multimedia and Electronics - Communication Technology (compulsory course in the program)
- Communications, Multimedia and Electronics - Multimedia Technology (compulsory course in the program)
- Communications, Multimedia and Electronics - Applied Electronics (compulsory course in the program)
- Communications, Multimedia and Electronics - Network and Information Technology (compulsory course in the program)
- Open Informatics - Computer Systems (elective course)
- Open Informatics - Computer and Information Science (elective course)
- Open Informatics - Software Systems (elective course)
- Electrical Engineering, Power Engineering and Management (elective course)
- Communications, Multimedia and Electronics (compulsory course in the program)
- Cybernetics and Robotics (elective course)
- Open Informatics (elective course)
- Communications, Multimedia and Electronics - Communications and Electronics (compulsory course in the program)